As an Amazon Associate I earn from qualifying purchases.
1. WOWOONE #ad
WOWOONE 1Pcs PWM to Voltage Module 0%-100% PWM to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards #adWOWOONE #ad
- It can be used to switch the signal interface of PLC or other industrial control board. Pwm signal receiving frequency range: 1KHZ-3KHZ.
The module is small, easy to carry and easy to use. The pwm to voltage module converts pwm digital signals to 0 to 10v analog signals. Adjust the output voltage by adjusting the PWM duty cycle.
Easy to operate, can be fine-tuned by potentiometer. Using mcu embedded technology. Select the pwm signal input level range by short circuit. Module working voltage: dC 12V-30V; current greater than 100mA. The module is small in size and easy to apply in different places.
2. Colorful-USA #ad
0-10v LED Dimming Controller 0-10V Analog Dimming Signal To Constant Voltage PWM 5A x 3CH RGB #adColorful-USA #ad
- Max output 5a*3ch, 15A in total. Compatible with many brand dimming systems. 0 - 10v to pwm dimming signal conversion. Working voltage from DC12V~DC24V. Optical isolation protection for input & output.
3. Laser-makers #ad
PWM To Voltage 0-5V/0-10V Duty Cycle 0-100% Linear Conversion Transmitter Module #adLaser-makers #ad
- Working voltage: 9V ~ 24V. Input voltage range : 4 ~ 24V. We will ship it within 1-2 days, it may takes 7-12 days to USA by Standard Shipping. Output voltage: 0v ~ 5v / 0V ~ 10V.
4. NOYITO #ad
Pulse Signal To Analog Voltage PWM Converter For Servo Test Signal Calibration, NOYITO Multifunction Signal Converter Module PT01A Servo Signal to Voltage and PWM Signal #adNOYITO #ad
- Limit input voltage:4. 5vmin, 5. 5v max low jumper position; 6. 0vmin, 15vmaxhigh jumper position;. Application:calibration servo signal, Potentiometer or joystick control servo, RC control motor speed controller.
Br>. Limit output current : 6. 5. A / 7. 5a; current: ＜10mA；. Operating voltage : ± dc 5v （low jumper position ）; DC7V to DC15V High jumper position;. Test servos :analog voltage signal to ppm signals, PPM signal to Analog voltage signals, PPM signal to PWM signal. Br>.
5. ANGGREK #ad
Low Voltage DC Motor Speed Controller PWM 1803BK 1.8V 3V 5V 6V 12V 15V 2A Low Voltage Speed Regulator Control Module Adjustable Driver 1.8V to 15V #adANGGREK #ad
- With a power-On LED light. Regulate range: Input Voltage: DC 1. 8 v-15 v ; current: Lower than 2A. Pulse width modulation : pwm ; the maximum output power: 30w. This is a speed governor with a maximum current of 2A.
It is not recommended to supply power greater than 12V, which may cause damage to the governor. Connect to dc power, never connect to 220 v ac power. Mini dc motor speed controller provide a speed regulation to your DC brush motor or other DC load.
Over current protection : self-recovery fuse this mini controller will be disconnected automatically if the current is too large and the fuse will recover automatically after cooling.
If the continuous current is greater than 05a, such as 12v lead-acid batteries, the 775 motor and the stroller motor will not move. Note: the potentiometer has no switching function. Easy to install and operate: Panel mounted, uses screw terminals for convenient and quick wiring.
6. NOYITO #ad
NOYITO DC Control 4-Channel FET Module MOS Electronic Switch Control Board Output Controlled Voltage 5V-36V 5A Input Output Completely Isolated #adNOYITO #ad
- Product wiring diagram, please see the second picture on the left. Can be connected to the microcontroller IO port, DC power supply, PLC interface, etc.
Br>. Input signal voltage: 3v-24v; current: about 5ma. Dc control 4-channel fet module, the input and output are completely isolated. The output is suitable for controlling high-power equipment, micro pumps, DC motors, solenoid valves, bulbs, LED strips, motors, etc.
Br>. Current: less than 5a, more than 5A need to add heat sink, the maximum can not exceed 20A. Br>. Signal trigger terminal: digital high and low level. The f5305s power fet is used. Br>. Output controlled voltage: 7v-36v.
7. Onyehn #ad
Onyehn 5Pcs 1.8v 3v 5v 6v 7.2v 12v 2A 30W Low Voltage DC Motor Speed Controller PWM 1803BK 1803B Adjustable Driver Switch 5 Pack #adOnyehn #ad
- If the current is too large, it will be automatically disconnected, and the fuse will automatically recover after cooling. If the continuous current is greater than 05a, the 775 motor and the stroller motor will not move.
Pwm dc motor speed controller with switch function. This is a speed governor with a maximum current of 2a. It is not recommended to supply power greater than 12V, such as 12V lead-acid batteries, which may cause damage to the governor.
With a self-recovery fuse 2A and a Power-On LED light. Don't buy it wrong. This brand new 1803bk dc motor speed controller allows controlling the direction of a DC the motor using a Pulse-Width-Modulated PWM DC voltage with a Duty Cycle fully the product adjust from 0%-100%.
8. Happyskymall #ad
DIY LED U-Home 3Pcs DC3V-35V DC 3V 6V 12V 24V 35V Variable Voltage Regulator 5A PWM Speed Controller Switch Dimmer for DIY LED Panel Light Single Color LED Strip Light SMD5050/SMD5630/SMD3528 #adHappyskymall #ad
- Please note: the operating voltage can be switched to 3-15v by bridging the connectors marked '3-15v' on the PCB. By screwing the potentiometer, overcurrent automatic disconnection, you can turn off power supply output.
Package included : 3 x PWM Speed Dimmer Controller. Mini dc 3-35v 5a pwm motor speed controller.
Wide voltage dc motor speed controller, PWM duty cycle: 1% -100%. Mini dc motor speed controller. High voltage and high current resettable fuse, power off for cooling for a few seconds fuses automatic recovery. Default disconnection of short circuit point. Pwm led dimmer for diy led Panel Light LED Strip Light.
9. Quentacy #ad
Quentacy DC 0/1-10V Knob Mini Dimmer Controller Rotary Switches PWM Dimming for LED Light Interior Lighting Dimmable Spotlight Grow Lamp LED Driver #adQuentacy #ad
- Designed for 0/1-10v regulating and compatible all 0/1-10V interface dimmable electronic LED Driver & ballasts & transformers and power dimmers. The dimmer is small and easy to install, switch Size: 34*22*15（mm）, Mounting Hole Diameter :φ7mm.
The connected power 0/1-10v interface must have a voltage of 10V for dimming, Adjustment range: 1-100%. The max load connected to the drive is 10V/40mA. Place the driver away from direct heat sources and in well-aired spaces. If the driver is built-in, sufficient ventilation must be ensured.